P D F - S E A R C H

Found 14 mln. answers for '../etc/passwd'[0]'A=0'A=0'.

Adding New users | etc/passwd File
Edit passwd and shadow files Set an initial password Create home directory For the user Copy default startup files to the user’s home directory Set the user’s mail home and establish mail aliases if applicable Others Add the user to /etc/group file Configure disk quotas Verify the account.

http://www.csl.mtu.edu/cs3451/www/notes/ch6%20-%20Adding%20new%20users.pdf

Securing Password Storage
qq Circa 1973 qq ‘one-­‐way’ password encryption qq chmod a+r /etc/passwd qq DES took 1 sec per password. © 2013 Cigital Inc. All Rights Reserved. Proprietary and Condential.

http://sconce.ics.uci.edu/134-W14/Securing-Password%E2%80%93Storage-RW.pdf

Cannot usually log in as root remotely | etc/passwd
files by default ● Gecos: extra information about you, typically a comma separated. list of name, building/room number, phone number and other contact info ● Home: Where in the file system to point the working directory on login ● Program: What program to run once you login. /etc/shadow.

https://courses.cs.washington.edu/courses/cse484/11au/sections/section6.pdf

Lecture 5
§ For instance, a gollum function that uses registers $a0, $a2, $s0 and $s2 could save the original values first, and restore them before returning. § But the callee does not know what registers are important to the caller, so again it may save more registers than necessary.

https://courses.cs.washington.edu/courses/cse378/09wi/lectures/lec05.pdf

Chapter 23
x axis due to a point charge fixed at the origin 6.00 kV·m and x ≠ 0 . (a) Find the magnitude.

http://faculty.washington.edu/mrdepies/122spring08/hw_soln/Ch23%20ISM.pdf

Introduction to Computer Security | etc/passwd examples
User account information: /etc/passwd. 1. Username: used when user logs in, 1–32 characters long 2. Password: ’x’ indicates that encrypted password is stored in. 1. Username: the user name 2. Passwd: the encrypted password 3. Last: days since Jan 1, 1970 that password was last.

http://www.ra.cs.uni-tuebingen.de/lehre/ss11/introsec/08-unix.pdf

CUMA OS Password Reset Fails with the
11. Run the passwd root command and give a password at the prompt, then confirm. Now you will have root access when you boot into the active passwd admin, where admin is your OS Administrator's user login name. Note: Here, the password is only used temporarily. You will need to do it again.

https://www.cisco.com/c/en/us/support/docs/voice-unified-communications/unified-mobility/112908-cuma-pwd.pdf

Configuring the ASA CX Module
asacx> config passwd The password must be at least 8 characters long and must contain at least one uppercase letter (A-Z), at least one lowercase letter (a-z) and at least one digit (0-9). Enter password: Farscape1 Confirm password: Farscape1 SUCCESS: Password changed for user admin.

https://www.cisco.com/c/en/us/td/docs/security/asa/asa91/asdm71/firewall/asdm_71_firewall_config/modules_cx.pdf

Configure Persistent Logging on Cisco IOS
Typically, logging messages (warnings, error and/or debugs etc.) are stored in a router's memory buffer (DRAM); when the buffer is full, older messages are overwritten by new messages. This. poses an issue when trying to capture debugs for an intermittent issue or during high traffic.

https://www.cisco.com/c/en/us/support/docs/voice/telephony-signaling/212102-Configure-Persistent-Logging-on-Cisco-IO.pdf

Unit 14 | etc/security/failedlogin
# pwdadm username • SMIT invokes the passwd command • An ordinary user can use the passwd command to. change own password • Only root or member of security group can change. © Copyright IBM Corporation 2008. /etc/security/passwd file.

http://www.mi.fu-berlin.de/wiki/pub/Tec/ArtLehreSystemverwaltung2009/AIXSysAdminI_14_UserSec.pdf